; VIDEO COMPOSITE PAL IO DEVICE
;
; INTERFACING WITH PAT80:
; Use PortB as data port. Before writing anything, issue a read (pin RW HIGH) and check the busy pin on the data port. 
; If the busy pin is high, retry reading until goes low. When the busy pin goes low, we have... TODO
;
; ELECTRONICALLY:
; The data port PB0 is tied to ground with a 1KOhm resistance. When the MC is busy drawing the screen, the data port is in
; high impedance state, so that avoids causing bus contention, but when read returns a 0bXXXXXXX0 byte. When the MC starts vsync,
; begins checking the port for data... TODO
;
; PINS:
; Video:
;     Video pin: PA0 (pin 1) (but all PORTA is used)
;     Sync pin: PC0 (pin 22)
; Communication:
;     Data port is PORTB [INPUT]
;     CLK (clock) signal is on PORTD0 [INPUT]
;     RS (register select) on PORTD1 [INPUT]
;     BUSY signal is on PORTD2 [OUTPUT]
; Debug:
;     Debug hsync single pulse on pin: PC1 (pin 23) (may be disabled)
;

.include "m1284def.inc" ; Atmega 1280 device definition

; *** reserved registers ***
; Cursor Position
;     POS_COLUMN (0-46) represents the character/chunk column
;     POS_ROWP (0-255) represent the chunk row. The caracter row is POS_ROWP/FONT_HEIGHT
;     POS_FINE represents fine position (bit inside coarse-position-pointed chunk) in graphic mode.
.def POS_COLUMN = r21
.def POS_ROWP = r20
.def POS_FINE = r24
; Internal registers
.def A = r0	; accumulator
.def STATUS = r25	; signal status (see STATUS TABLE)
;POS_COARSE = Y	; coarse position (aligned to character column)
;DRAWING_BYTE = X	; current position in framebuffer
.def LINE_COUNTER = r23
.def VG_HIGH_ACCUM = r22 ; an accumulator in high registers to be used only by video_generator in interrupt
.def HIGH_ACCUM = r16 ; an accumulator in high registers to be used outside of interrupts

; define constant
.equ VIDEO_PORT_OUT = PORTA		; Used all PORTA, but connected only PA0
.equ SYNC_PIN = PC0			; Sync pin (pin 22)
.equ DEBUG_PIN = PC1		; DEBUG: Single vertical sync pulse to trigger oscilloscope (pin 23)
.equ DATA_PORT_IN = PINB
.equ CLK_PIN = PD0
.equ RS_PIN = PD1
.equ BUSY_PIN = PD2

; memory
.equ FRAMEBUFFER = 0x0100
.equ FRAMEBUFFER_END = 0x2F00
.equ SCREEN_HEIGHT = 256

; start vector
.org 0x0000
	rjmp	main			; reset vector: jump to main label
.org 0x001E
	rjmp	on_tim1_ovf		; interrupt for timer 1 overflow (used by video generation)

.org 0x40
; main program
main:
	; **** I/O SETUP ****

	; pins setup
	sbi	DDRC, SYNC_PIN		; set pin as output
	sbi	DDRC, DEBUG_PIN		; set pin as output
	sbi	DDRC, BUSY_PIN		; set pin as output
	cbi DDRD, CLK_PIN		; set pin as input
	ldi	HIGH_ACCUM, 0xFF
	out DDRA, HIGH_ACCUM			; set port as output (contains video pin)
	ldi	HIGH_ACCUM, 0x00
	out DDRB, HIGH_ACCUM			; set port as input (used as data bus)


	; **** MEMORY SETUP ****

	; clear ram
	;*** Load data into ram ***
	; Set X to 0x0100
	; ldi XH, high(FRAMEBUFFER)
	; ldi XL, low(FRAMEBUFFER)
	; load_mem_loop:
	; 	clr r17
	; 	st X+, r17
	; 	; if reached the last framebuffer byte, exit cycle
	; 	cpi XH, 0b00111110
	; 	brne load_mem_loop	; if not 0, repeat h_picture_loop
	; 	cpi XL, 0b11000000
	; 	brne load_mem_loop	; if not 0, repeat h_picture_loop

	



	; **** TIMERS AND DRAWING IMAGE ROUTINES SETUP ****

	; Timer setup (use 16-bit counter TC1)
	; The Power Reduction TC1 and TC3 bits in the Power Reduction Registers (PRR0.PRTIM1 and
	; PRR1.PRTIM3) must be written to zero to enable the TC1 and TC3 module.
	ldi HIGH_ACCUM, 0b00000000
	sts	PRR0, HIGH_ACCUM
	; Set timer prescaler to 1:1
    LDI HIGH_ACCUM,0b00000001
    sts TCCR1B,HIGH_ACCUM
	; Enambe timer1 overflow interrupt
    LDI HIGH_ACCUM,0b00000001
    STS TIMSK1,HIGH_ACCUM
	; Enable interrupts globally
    SEI
	; Timer setup completed.




	; **** MAIN ROUTINE ****

	; Wait for data (it never exits)
	; jmp comm_init


	; draw example image
	call draw_cat

	; test draw character routine
	call draw_carriage_return
	call draw_carriage_return
	call draw_carriage_return

	call cursor_pos_home
	ldi r18, 0x41
	dctest:
		draw_chars:
			mov HIGH_ACCUM, r18
			call draw_char
			inc r18
			cpi r18, 0x5B
			brne dc_continue
			ldi r18, 0x41
			call draw_carriage_return
			dc_continue:
			; wait
			ser r19
			dc_wait_loop_1:
				ser r20
				dc_wait_loop_2:
					dec r20
					brne dc_wait_loop_2
				dec r19
				brne dc_wait_loop_1
			brne draw_chars
		jmp dctest

	


	forever:
		jmp forever




.include "video_generator.asm" ; Asyncronous timer-interrupt-based video generation
.include "character_generator.asm" ; Character generator
;.include "communication.asm" ; Communication with Pat80
.include "font.asm"	; Font face
.include "example_data/cat.asm"	; Cat image